Högskolan i Skövde

his.sePublikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • apa-cv
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Experimental analysis of cutting edge effects on vibrations in end milling
Seco Tools, Fagersta, Sweden ; University West, Department of Engineering Science, Trollhättan, Sweden.ORCID-id: 0000-0003-3876-2361
University West, Department of Engineering Science, Trollhättan, Sweden.ORCID-id: 0000-0001-9331-7354
Lund University, Production and Materials Engineering, Sweden.
University West, Department of Engineering Science, Trollhättan, Sweden.ORCID-id: 0000-0003-0976-9820
2019 (Engelska)Ingår i: CIRP - Journal of Manufacturing Science and Technology, ISSN 1755-5817, E-ISSN 1878-0016, Vol. 24, s. 66-74Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The ability to minimize vibrations in milling by the selection of cutting edge geometry and appropriate cutting conditions is an important asset in the optimization of the cutting process. This paper presents a measurement method and a signal processing technique to characterize and quantify the magnitude of the vibrations in an end milling application. Developed methods are then used to investigate the effects of various cutting edge geometries on vibrations in end milling. The experiments are carried out with five cutting edge geometries that are frequently used in machining industry for a wide range of milling applications. The results show that a modest protection chamfer combined with a relatively high rake angle has, for the most of cutting conditions, a reducing effect on vibration magnitudes. Furthermore, dynamics of a highly positive versus a highly negative cutting geometry is explored in time domain and its dependency on cutting conditions is presented. The results give concrete indications about the most optimal cutting edge geometry and cutting conditions in terms of dynamic behavior of the tool.

Ort, förlag, år, upplaga, sidor
Elsevier, 2019. Vol. 24, s. 66-74
Nyckelord [en]
Milling, Acceleration, Cutting edge, Frequency spectrum, Rake angle, Chamfer
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Identifikatorer
URN: urn:nbn:se:his:diva-22348DOI: 10.1016/j.cirpj.2018.11.001ISI: 000460558000007Scopus ID: 2-s2.0-85057229226OAI: oai:DiVA.org:his-22348DiVA, id: diva2:1748002
Forskningsfinansiär
KK-stiftelsen
Anmärkning

This paper presents the results of a joint work between Seco Tools AB and University West in Sweden. Funding of the project, provided by Seco Tools and the KK foundation, is highly appreciated. Support from The Research School of Simulation and Control of Material affecting Processes (SiCoMaP) is also gratefully acknowledged.

Tillgänglig från: 2019-03-21 Skapad: 2023-03-31 Senast uppdaterad: 2025-09-29Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Person

Agic, AdnanEynian, MahdiBeno, Tomas

Sök vidare i DiVA

Av författaren/redaktören
Agic, AdnanEynian, MahdiBeno, Tomas
I samma tidskrift
CIRP - Journal of Manufacturing Science and Technology
Bearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 367 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • apa-cv
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf