Högskolan i Skövde

his.sePublikationer
Ändra sökning
Länk till posten
Permanent länk

Direktlänk
Svensson, Daniel
Publikationer (10 of 14) Visa alla publikationer
Andersson, T., Svensson, D. & Andersson Lassila, A. (2024). Modelling and simulation of heat flow in indexable insert drilling. The International Journal of Advanced Manufacturing Technology, 131(9-10), 5177-5192
Öppna denna publikation i ny flik eller fönster >>Modelling and simulation of heat flow in indexable insert drilling
2024 (Engelska)Ingår i: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 131, nr 9-10, s. 5177-5192Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

In machining, the heat generated during the process deforms the components and the final shape might not meet specified tolerances. There is therefore a need for a compensation strategy which requires knowledge of the workpiece temperature field and the associated thermal distortions. In this work, a methodology is presented for the determination of the heat load for indexable insert drilling of AISI 4140. Compared to previous research, this work has introduced a varying heat load. The heat load is extracted from thermo-mechanical finite element simulations for different nominal chip thicknesses and cutting speeds using the coupled Eulerian-Lagrangian formulation of an orthogonal turning process. The heat load is then transferred to a simplified 2D axisymmetric heat transfer model where the in-process temperature field in the workpiece is predicted. To verify the methodology, the predicted temperatures are compared to the experimentally measured temperatures for various feed rates. It is found that the model is capable of predicting the workpiece temperatures reasonably well. However, the methodology needs to be further explored to validate its applicability.

Ort, förlag, år, upplaga, sidor
Springer Nature, 2024
Nyckelord
Machining, Indexable drilling, FEM, Heat flow simulation, Experimental verification
Nationell ämneskategori
Energiteknik Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Virtual Manufacturing Processes
Identifikatorer
urn:nbn:se:his:diva-23644 (URN)10.1007/s00170-024-13224-4 (DOI)001171672000001 ()2-s2.0-85186914915 (Scopus ID)
Projekt
CoSim
Forskningsfinansiär
Högskolan i SkövdeKK-stiftelsen, 20160298
Anmärkning

CC BY 4.0 DEED

Published: 02 March 2024

The authors would like to acknowledge the Swedish Knowledge Foundation for funding of the CoSim project (Dnr:20160298). We also want to thank Powertrain Engineering Sweden AB and Automotive Components Floby AB for their support and collaboration during the project.

Open access funding provided by University of Skövde. The research leading to these results received funding from the Swedish Knowledge Foundation under Grant Agreement No 20160298.

Tillgänglig från: 2024-03-04 Skapad: 2024-03-04 Senast uppdaterad: 2025-09-29Bibliografiskt granskad
Andersson Lassila, A., Svensson, D., Wang, W. & Andersson, T. (2024). Numerical evaluation of cutting strategies for thin-walled parts. Scientific Reports, 14(1), Article ID 1459.
Öppna denna publikation i ny flik eller fönster >>Numerical evaluation of cutting strategies for thin-walled parts
2024 (Engelska)Ingår i: Scientific Reports, E-ISSN 2045-2322, Vol. 14, nr 1, artikel-id 1459Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Static form errors due to in-process deflections is a major concern in flank milling of thin-walled parts. To increase both productivity and part geometric accuracy, there is a need to predict and control these form errors. In this work, a modelling framework for prediction of the cutting force-induced form errors, or thickness errors, during flank milling of a thin-walled workpiece is proposed. The modelled workpiece geometry is continuously updated to account for material removal and the reduced stiffness matrix is calculated for nodes in the engagement zone. The proposed modelling framework is able to predict the resulting thickness errors for a thin-walled plate which is cut on both sides. Several cutting strategies and cut patterns using constant z-level finishing are studied. The modelling framework is used to investigate the effect of different cut patterns, machining allowance, cutting tools and cutting parameters on the resulting thickness errors. The framework is experimentally validated for various cutting sequences and cutting parameters. The predicted thickness errors closely correspond to the experimental results. It is shown from numerical evaluations that the selection of an appropriate cut pattern is crucial in order to reduce the thickness error. Furthermore, it is shown that an increased machining allowance gives a decreased thickness error for thin-walled plates.

Ort, förlag, år, upplaga, sidor
Springer Nature, 2024
Nationell ämneskategori
Teknisk mekanik Reglerteknik Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Virtual Manufacturing Processes; Virtual Production Development (VPD)
Identifikatorer
urn:nbn:se:his:diva-23541 (URN)10.1038/s41598-024-51883-1 (DOI)001144007600001 ()38228725 (PubMedID)2-s2.0-85182423435 (Scopus ID)
Forskningsfinansiär
Högskolan i SkövdeKK-stiftelsen, 20180168
Anmärkning

CC BY 4.0 DEED

School of Engineering Science, University of Skövde, Kaplansgatan 11, SE‑541 34 Skövde, Sweden. *email: daniel.svensson@his.se

Open access funding provided by University of Skövde. This work was supported financially by the Swedish Knowledge Foundation through the project SIMPLE (dnr: 20180168).

Tillgänglig från: 2024-01-17 Skapad: 2024-01-17 Senast uppdaterad: 2025-09-29Bibliografiskt granskad
Andersson, T., Svensson, D., Andersson Lassila, A., Trujillo Vilches, F. J. & Bermudo Gamboa, C. (2023). 3D-Simulation of Heat Flow in Indexable Drilling. Key Engineering Materials, 955, 53-62
Öppna denna publikation i ny flik eller fönster >>3D-Simulation of Heat Flow in Indexable Drilling
Visa övriga...
2023 (Engelska)Ingår i: Key Engineering Materials, ISSN 1013-9826, E-ISSN 1662-9795, Vol. 955, s. 53-62Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

In machining, the heat flow into the workpiece during the cutting process is often a major concern. The temperature rise can lead to substantial residual stresses or elastic in-process deformations which may result in the dimensional tolerance requirements being violated. In the present study a modelling strategy is developed for determination of the heat load during indexable drilling. The heat load on the workpiece is determined from 3D thermomechanical Coupled Eulerian Lagrangian analyses of orthogonal turning for various chip thicknesses and cutting speeds. The determined heat load is then transferred to a 3D transient heat transfer analysis of the indexable drilling process for the determination of the temperature field. Thereby, this modelling technique avoids the complex cutting process that is performed in real cutting simulations and thereby reducing the computational complexity of the problem considerably. The simulated temperatures are compared with experimentally measured temperatures and some conclusions are drawn regarding the modelling approach.

Ort, förlag, år, upplaga, sidor
Scientific.Net, 2023
Nyckelord
CEL Simulation, FEM, Heat Load, Indexable Drilling
Nationell ämneskategori
Teknisk mekanik Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Virtual Manufacturing Processes
Identifikatorer
urn:nbn:se:his:diva-23526 (URN)10.4028/p-u1wzfu (DOI)
Anmärkning

Scientific.Net is a registered brand of Trans Tech Publications Ltd

Tillgänglig från: 2024-01-15 Skapad: 2024-01-10 Senast uppdaterad: 2025-09-29Bibliografiskt granskad
Svensson, D., Andersson, T. & Andersson Lassila, A. (2022). Coupled Eulerian–Lagrangian simulation and experimental investigation of indexable drilling. The International Journal of Advanced Manufacturing Technology, 121(1-2), 471-486
Öppna denna publikation i ny flik eller fönster >>Coupled Eulerian–Lagrangian simulation and experimental investigation of indexable drilling
2022 (Engelska)Ingår i: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 121, nr 1-2, s. 471-486Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

In many industries, indexable insert drills are used to cost effectively produce short holes. However, common problems such as chatter vibrations, premature tool wear and generation of long curly chips that cause poor chip evacuation make optimization of the drilling process challenging and time-consuming. Therefore, robust predictive models of indexable drilling processes are desirable to support the development towards improved tool designs, enhanced cutting processes and increased productivity. This paper presents 3D finite element simulations of indexable drilling of AISI4140 workpieces. The Coupled Eulerian–Lagrangian framework is employed, and the focus is to predict the drilling torque, thrust force, temperature distributions and chip geometries. To reduce the computational effort, the cutting process is modelled separately for the peripheral and the central inserts. The total thrust force and torque are predicted by superposing the predicted result for each insert. Experiments and simulations are conducted at a constant rotational velocity of 2400 rpm and feed rates of 0.13, 0.16 and 0.18 mm/rev. While the predicted torques are in excellent agreement, the thrust forces showed discrepancies of 12 - 20% to the experimental measured data. Effects of the friction modelling on the predicted torque and thrust force are outlined, and possible reasons for the thrust force discrepancies are discussed in the paper. Additionally, the simulations indicate that the tool, chip and the local workpiece temperature distributions are virtually unaffected by the feed rate.

Ort, förlag, år, upplaga, sidor
Springer Nature Switzerland AG, 2022
Nyckelord
Machining, Indexable drilling, Finite Element Method (FEM), AISI4140, Coupled Eulerian Lagrangian (CEL)
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Virtual Manufacturing Processes
Identifikatorer
urn:nbn:se:his:diva-21127 (URN)10.1007/s00170-022-09275-0 (DOI)000796322500002 ()2-s2.0-85130129433 (Scopus ID)
Forskningsfinansiär
KK-stiftelsen, 20160298
Anmärkning

CC BY 4.0

Springer

© 2022 Springer Nature Switzerland AG. Part of Springer Nature.

Published: 16 May 2022

Open access funding provided by University of Skövde. This work was supported financially by the Swedish Knowledge Foundation through the project CoSim (dnr: 20160298).

Tillgänglig från: 2022-05-10 Skapad: 2022-05-10 Senast uppdaterad: 2025-09-29Bibliografiskt granskad
Bermudo Gamboa, C., Andersson, T. J., Svensson, D., Trujillo Vilches, F. J., Martín-Béjar, S. & Sevilla Hurtado, L. (2021). Modeling of the fracture energy on the finite element simulation in Ti6Al4V alloy machining. Scientific Reports, 11(1), Article ID 18490.
Öppna denna publikation i ny flik eller fönster >>Modeling of the fracture energy on the finite element simulation in Ti6Al4V alloy machining
Visa övriga...
2021 (Engelska)Ingår i: Scientific Reports, E-ISSN 2045-2322, Vol. 11, nr 1, artikel-id 18490Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

One of the main problems that exists when working with Finite Element Methods (FEM) applied to machining processes is the lack of adequate experimental data for simulating the material properties. Moreover, for damage models based on fracture energy, the correct selection of the energy value is critical for the chip formation process. It is usually difficult to obtain the fracture energy values and requires complex tests. In this work, an analysis of the influence of this fracture energy on the cutting force and the chip generation process has been carried out for different sets of cutting parameters. The aim is to present an empirical relationship, that allows selecting the fracture energy based on the cutting force and cutting parameters. The work is based on a FEM model of an orthogonal turning process for Ti6Al4V alloy using Abaqus/Explicit and the fracture energy empirical relation. This work shows that it is necessary to adjust the fracture energy for each combination of cutting conditions, to be able to fit the experimental results. The cutting force and the chip geometry are analyzed, showing how the developed model adapts to the experimental results. It shows that as the cutting speed and the feed increase, the fracture energy value that best adapts to the model decreases. The evolution shows a more pronounced decrease related to the feed increment and high cutting speed. 

Ort, förlag, år, upplaga, sidor
Springer Nature, 2021
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Virtual Manufacturing Processes
Identifikatorer
urn:nbn:se:his:diva-20614 (URN)10.1038/s41598-021-98041-5 (DOI)000696635300022 ()34531521 (PubMedID)2-s2.0-85115316893 (Scopus ID)
Anmärkning

CC BY 4.0

© 2021, The Author(s).

Correspondence and requests for materials should be addressed to C.B.G.

Tillgänglig från: 2021-09-30 Skapad: 2021-09-30 Senast uppdaterad: 2025-09-29
Trujillo, F. J., Bermudo, C., Martín-Béjar, S., Svensson, D., Andersson, T. J. & Sevilla, L. (2021). Shrinkage Factor Analysis in the Dry Machining of UNS A92024 Alloy by FEM. In: Angelos P. Markopoulos; Irene P. Koronaki; Laurenţiu Slatineanu; Gheorghe Cretu; Oana Dodun; Andrei Marius Mihalache (Ed.), 24th Innovative Manufacturing Engineering and Energy International Conference (IManEE 2020) 14th-15th December 2020, Athens, Greece: . Paper presented at 24th Innovative Manufacturing Engineering and Energy International Conference (IManEE 2020) 14th-15th December 2020, Athens, Greece. Institute of Physics (IOP), 1037
Öppna denna publikation i ny flik eller fönster >>Shrinkage Factor Analysis in the Dry Machining of UNS A92024 Alloy by FEM
Visa övriga...
2021 (Engelska)Ingår i: 24th Innovative Manufacturing Engineering and Energy International Conference (IManEE 2020) 14th-15th December 2020, Athens, Greece / [ed] Angelos P. Markopoulos; Irene P. Koronaki; Laurenţiu Slatineanu; Gheorghe Cretu; Oana Dodun; Andrei Marius Mihalache, Institute of Physics (IOP), 2021, Vol. 1037Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Chip evacuation becomes a relevant factor in the dry machining of aeronautical aluminium alloys, either when they are machined as isotropic material or hybridized with other materials. Chip morphology and geometry highly depend on cutting parameters. Several works can be found in the literature focusing on the analysis of chip morphology of aluminium alloys at high cutting speeds but there is a lack of studies that apply low cutting speeds. FEM simulation may be useful to reduce the experimental time and cost of this kind of analysis. Therefore, in this work, the influence of feed-rate on several chip geometrical parameters (height of peaks, height of valleys and shrinkage factor) of dry turned UNS A92024 alloy has been analysed by FEM simulation. Three different energy fracture modes have been tested as damage evolution criterion, in order to get the mode that better fit the experimental chip morphology. In general, the mixed mode was the fracture energy mode that best suited the chip morphology behaviour, within wider feed-rate range.

Ort, förlag, år, upplaga, sidor
Institute of Physics (IOP), 2021
Serie
IOP Conference Series: Materials Science and Engineering, ISSN 1757-8981, E-ISSN 1757-899X ; 1037
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Virtual Manufacturing Processes
Identifikatorer
urn:nbn:se:his:diva-19484 (URN)10.1088/1757-899X/1037/1/012011 (DOI)2-s2.0-85101645808 (Scopus ID)
Konferens
24th Innovative Manufacturing Engineering and Energy International Conference (IManEE 2020) 14th-15th December 2020, Athens, Greece
Anmärkning

CC BY 3.0

Tillgänglig från: 2021-02-22 Skapad: 2021-02-22 Senast uppdaterad: 2025-09-29
Stigh, U., Biel, A. & Svensson, D. (2016). Cohesive zone modelling and the fracture process of structural tape. Paper presented at 21st European Conference on Fracture, ECF21, 20-24 June 2016, Catania, Italy. Proceedia Structural Integrity, 2, 235-244
Öppna denna publikation i ny flik eller fönster >>Cohesive zone modelling and the fracture process of structural tape
2016 (Engelska)Ingår i: Proceedia Structural Integrity, ISSN 2452-3216, Vol. 2, s. 235-244Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Structural tapes provide comparable toughness as structural adhesives at orders of magnitude lower stresses. This is potentially useful to minimize the effects of differences in thermal expansion in the joining of mixed materials. The strength properties are modelled using the cohesive zone model. Thus, a cohesive zone represents the tape, i.e. stresses in the tape are transmitted to the substrates through tractions determined by the separations of the surfaces of substrates. This simplification allows for structural analysis of large complex structures. The relation between the traction and the separation is measured experimentally using methods based on the path independence of the J-integral. Repeated experiments are performed at quasi-static loading. A mixed mode cohesive law is adapted to the experimental data. The law is implemented as a UMAT in Abaqus. Simulations show minor thermal distortions due to thermal loading and substantial structural strength in mechanical loading of a mixed material structure.

Ort, förlag, år, upplaga, sidor
Elsevier, 2016
Nyckelord
Mixed material joint, structural strength, FEA, J-integral method
Nationell ämneskategori
Teknisk mekanik
Forskningsämne
Teknik; Materialmekanik
Identifikatorer
urn:nbn:se:his:diva-12733 (URN)10.1016/j.prostr.2016.06.031 (DOI)000387976800030 ()2-s2.0-85011855501 (Scopus ID)
Konferens
21st European Conference on Fracture, ECF21, 20-24 June 2016, Catania, Italy
Projekt
ÅForsk Tape
Forskningsfinansiär
ÅForsk (Ångpanneföreningens Forskningsstiftelse), 14-312
Anmärkning

"Open Access funded by European Structural Integrity Society"

Tillgänglig från: 2016-08-02 Skapad: 2016-08-02 Senast uppdaterad: 2025-09-29Bibliografiskt granskad
Svensson, D., Alfredsson, K. S., Stigh, U. & Jansson, N. E. (2016). Measurement of cohesive law for kink-band formation in unidirectional composite. Engineering Fracture Mechanics, 151, 1-10
Öppna denna publikation i ny flik eller fönster >>Measurement of cohesive law for kink-band formation in unidirectional composite
2016 (Engelska)Ingår i: Engineering Fracture Mechanics, ISSN 0013-7944, E-ISSN 1873-7315, Vol. 151, s. 1-10Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Kink-band formation is an important mechanism limiting the compressive strength of high strength composites. A cohesive zone model is used to model the material in a unidirectional carbon fibre composite that forms the kink-band. Equilibrium of configurational forces is used to design and evaluate the experiments. Microscopic studies show that a kink-band is formed with the height of about 200 μm. The corresponding cohesive law has a peak stress of about 1.5 GPa, a compression at failure of about 50 μm and a fracture energy of about 25 kJ/m2.

Ort, förlag, år, upplaga, sidor
Elsevier, 2016
Nyckelord
Composites, Configurational forces, DIC-measurement, Kink-band formation, Cohesive zone modelling
Nationell ämneskategori
Teknisk mekanik
Forskningsämne
Teknik; Materialmekanik
Identifikatorer
urn:nbn:se:his:diva-11717 (URN)10.1016/j.engfracmech.2015.10.040 (DOI)000368922000001 ()2-s2.0-84947934411 (Scopus ID)
Projekt
NFFP FiKomINFINIT MDC
Forskningsfinansiär
KK-stiftelsen, 20130305VINNOVA, NFFP 013223
Tillgänglig från: 2015-11-27 Skapad: 2015-11-27 Senast uppdaterad: 2025-09-29Bibliografiskt granskad
Svensson, D., Alfredsson, K. S. & Stigh, U. (2016). On the ability of coupled mixed mode cohesive laws to conform to LEFM for cracks in homogeneous orthotropic solids. Engineering Fracture Mechanics, 163, 426-448
Öppna denna publikation i ny flik eller fönster >>On the ability of coupled mixed mode cohesive laws to conform to LEFM for cracks in homogeneous orthotropic solids
2016 (Engelska)Ingår i: Engineering Fracture Mechanics, ISSN 0013-7944, E-ISSN 1873-7315, Vol. 163, s. 426-448Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The ability of coupled cohesive laws to conform to the predictions of linear elastic fracturemechanics (LEFM) in the case of small-scale-yielding (SSY) is explored. The study is concerned with cracks in homogeneous orthotropic solids and the results apply also for the case of isotropy. Both potential based and non-potential based cohesive laws are considered. It is shown that the initial stiffnesses of the cohesive law must be matched to the elastic moduli of the orthotropic solid in order to achieve a constant ratio of the cohesive stress components ahead of the crack tip. A simple condition for this is provided. For non potential based laws an additional apparently sufficient condition on the non-linear part of the cohesive law is identified: The traction vector must not change direction if the directionof the separation vector is constant. Fulfillment of this condition provides a uniform local mode mix in the cohesive zone with a value equal to the global mode mix. It is demonstrated that potential based cohesive laws display a varying local mode mix at the crack tip for cases with a mode dependent work of separation. This is identified as acomplicating feature in terms of calibrating the parameters of a cohesive law to experimental data.

Ort, förlag, år, upplaga, sidor
Elsevier, 2016
Nyckelord
Composites, Cohesive zone modelling, Finite element analysis, Delamination, Mixed mode fracture
Nationell ämneskategori
Teknisk mekanik
Forskningsämne
Teknik; Materialmekanik
Identifikatorer
urn:nbn:se:his:diva-12855 (URN)10.1016/j.engfracmech.2016.05.018 (DOI)000383309500027 ()2-s2.0-84989957760 (Scopus ID)
Projekt
MDC
Forskningsfinansiär
KK-stiftelsen
Tillgänglig från: 2016-08-31 Skapad: 2016-08-31 Senast uppdaterad: 2025-09-29Bibliografiskt granskad
Svensson, D. (2015). On Cohesive Modelling of Carbon/Epoxy Composites: Delamination and Fibre Compressive Failure. (Doctoral dissertation). Göteborg: Chalmers University of Technology
Öppna denna publikation i ny flik eller fönster >>On Cohesive Modelling of Carbon/Epoxy Composites: Delamination and Fibre Compressive Failure
2015 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

Carbon Fibre Reinforced Polymers are widely used in engineering applications where weight saving and high mechanical performance are a key factors. However, an inheren tweakness of laminated CFRP:s is there relatively low resistance to delamination. Therst part of this thesis is devoted to extract cohesive laws associated with delamination.The method is based on fracture mechanical tests and measurement of the displacementeld close to the crack tip. The second part of the thesis is concerned with mixed modecohesive modelling under small scale yielding conditions. Under such loading conditions,a robust cohesive model should conform to Linear Elastic Fracture Mechanics (LEFM). Itis shown that two design rules for mixed mode cohesive laws are sucient to achieve thisproperty. The third part focuses a failure mode entirely dierent from delamination. Theobjective is to determine cohesive laws associated with longitudinal compressive failure.Equilibrium of congurational forces is used for this purpose. Identied congurationalforces are continuously measured by monitoring the displacements eld on the specimen'slateral surface. This allows for identication of the cohesive law.

Ort, förlag, år, upplaga, sidor
Göteborg: Chalmers University of Technology, 2015
Serie
Doktorsavhandlingar vid Chalmers tekniska högskola, ISSN 0346-718X ; Ny serie nr. 3895
Nyckelord
CFRP, Cohesive zone model, J-integral, LEFM, Delamination, Compressive failure
Nationell ämneskategori
Teknisk mekanik
Forskningsämne
Teknik; Materialmekanik
Identifikatorer
urn:nbn:se:his:diva-10996 (URN)978-91-7597-214-5 (ISBN)
Disputation
2015-06-04, EA, Chalmers, Göteborg, 10:00 (Engelska)
Opponent
Handledare
Projekt
MDC
Tillgänglig från: 2015-06-05 Skapad: 2015-06-05 Senast uppdaterad: 2025-09-29Bibliografiskt granskad
Organisationer

Sök vidare i DiVA

Visa alla publikationer