Högskolan i Skövde

his.sePublications
Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • apa-cv
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Materialval för minskat slitage av sandformningsverktyg
University of Skövde, School of Engineering Science.
University of Skövde, School of Engineering Science.
2017 (Swedish)Independent thesis Basic level (degree of Bachelor), 20 credits / 30 HE creditsStudent thesisAlternative title
Material selection for reduced wear of sand forming tool (English)
Abstract [sv]

På Volvo Group Trucks Operations (GTO) i Skövde tillverkas cylinderblock, cylinderhuvud och svänghjul genom gjutning med sandformar. Då formverktygen som formar sandformarna fylls uppkommer slitage där sandpartiklarna träffar, vilket leder till att formverktygen behöver underhållas regelbundet.Målet med denna studie är att hitta alternativa material som formverktygen kan tillverkas i alternativt förstärkas eller beläggas med för att minska slitaget i formverktygen och på så sätt minska kostnader genom att förlänga underhållsintervallen. Problemet analyseras och en litteraturstudie kring erosiv och abrasiv nötning genomförs.Ett antal material tas fram genom en materialvalsprocess som lämpliga kandidater baserat på litteraturstudien, materialkartor och diskussion. Materialprover testas med en standardmetod för erosion med gasburna partiklar. Resultat från tidigare empiriska studier tyder på att erosion påverkas starkt av materialegenskaper så som hårdhet och seghet men även de eroderande partiklarnas infallsvinkel och hastighet.Erosionstestet utförs för 30 och 90 graders infallsvinkel. Testet visar att de mjukare stålen, Holdax och Sverker 21, har högre beständighet mot erosion vid låga infallsvinklar och det hårdare stålet Nimax har högre beständighet vid höga infallsvinklar. Nimax anses vara ett lämpligt material till formverktyget då Nimax har den totalt lägsta erosionstakten vid hopslagning av den totala erosionstakten över båda infallsvinklarna. Nimax har den lägsta erosionstakten vid 30 graders infallsvinkel och anses även ha god beständighet mot erosion vid 90 graders infallsvinkel.Rekommendation ges kring upprepade erosionstester för att säkerställa resultatet. Rekommendationer finns också kring materialprovning i formverktyget för att se om ett materialbyte skulle leda till besparingar. Undersökning av möjligheter att konstruera bort nötning i formverktyget genom ändring av infallsvinklar mellan den inblåsta sanden och formverktyget, samt ändring av lufttryck rekommenderas.

Abstract [en]

At Volvo Group Trucks Operations (GTO) in Skövde, cylinder blocks, cylinder heads and flywheels are manufactured through sandcasting. As the forming tools that forms the sand forms are filled with sand, wear occurs where the sand particles hit the tool surface. The forming tool thus needs to be regularly maintained. The aim of this study is to evaluate alternative materials that the forming tools can be manufactured in to reduce wear, and thereby reducing costs by extending maintenance intervals. The problem is analyzed and a literature study on erosive and abrasive wear is carried out. A number of materials are presented as suitable candidates based on the literature study, material charts and discussion. Material samples are tested using a standard method for solid particle erosion using gas jets. Results from previous empirical studies indicate that erosion is strongly influenced by material properties such as hardness and toughness but also the angle of impingement and velocity of the erosive particles.The erosion test is performed at 30 and 90 degree angle of impingement. The test shows that the softer steel, Holdax and Sverker 21 have higher resistance to erosion at low angles of impingement and the harder steel Nimax has higher resistance at high angles of impingement. Nimax is considered a suitable material for the forming tool, as Nimax has the overall lowest erosion rate when adding the total erosion over both angles of impingement. Nimax has the lowest erosion rate at 30 degrees angle and is also considered to have good resistance to erosion at 90 degrees angle. Recommendation is given on repeated erosion tests to validate the results. There are also recommendations regarding material testing in the forming tool to see if a material change would lead to savings. Examination of possibilities to make changes in the sand filling process, altering angle of impingement between the sand blown and the forming tool as well as air pressure is recommended.

Place, publisher, year, edition, pages
2017. , p. 51
Keywords [en]
Sand casting, Erosion, Materials science
Keywords [sv]
Sandgjutning, Erosion, Materialvetenskap
National Category
Tribology (Interacting Surfaces including Friction, Lubrication and Wear) Mechanical Engineering
Identifiers
URN: urn:nbn:se:his:diva-13776OAI: oai:DiVA.org:his-13776DiVA, id: diva2:1112008
External cooperation
Volvo GTO Skövde
Subject / course
Mechanical Engineering
Educational program
Mechanical Engineer
Presentation
2017-05-23, A303, Högskolan i Skövde, Skövde, 10:00 (Swedish)
Supervisors
Examiners
Available from: 2017-06-20 Created: 2017-06-19 Last updated: 2018-01-13Bibliographically approved

Open Access in DiVA

Materialval för minskat slitage av sandfomningsverktyg(2435 kB)602 downloads
File information
File name FULLTEXT01.pdfFile size 2435 kBChecksum SHA-512
34473abc87ffd32a768def4cefca37164f9344ee20e08188ce19fcb6dce24255a43275f648e52ef980bd57a7a7274c5af0ba3f6022941eecfd28ef871ac0c3db
Type fulltextMimetype application/pdf

Search in DiVA

By author/editor
Hermansson, JakobWahlström, Emma
By organisation
School of Engineering Science
Tribology (Interacting Surfaces including Friction, Lubrication and Wear)Mechanical Engineering

Search outside of DiVA

GoogleGoogle Scholar
Total: 602 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

urn-nbn

Altmetric score

urn-nbn
Total: 1003 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • apa-cv
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf