his.sePublikasjoner
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Effects of constitutive parameters on the accuracy of measured fracture energy using the DCB-specimen
Högskolan i Skövde, Institutionen för teknik och samhälle.
Högskolan i Skövde, Institutionen för teknik och samhälle.
2008 (engelsk)Inngår i: Engineering Fracture Mechanics, ISSN 0013-7944, E-ISSN 1873-7315, Vol. 75, nr 10, s. 2968-2983Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Several methods exist to estimate the fracture energy for adhesive joints using the double cantilever beam specimen and linear elastic fracture mechanics. Since the mechanical properties of all adhesives are non-linear, errors are generated. By use of an exact solution experiments are simulated. These are evaluated with eight different methods. The influence of the constitutive parameters is systematically studied. This influence is small for most methods. The error due to the choice of evaluation method is considerably larger. One of the commonly used methods gives accurate results; the error is less than 3%. However, most methods yield substantial errors.

sted, utgiver, år, opplag, sider
Elsevier, 2008. Vol. 75, nr 10, s. 2968-2983
Emneord [en]
Test standards, DCB-specimen, Toughness testing, Fracture energy, Adhesive
HSV kategori
Forskningsprogram
Teknik
Identifikatorer
URN: urn:nbn:se:his:diva-2806DOI: 10.1016/j.engfracmech.2008.01.002ISI: 000256014600009Scopus ID: 2-s2.0-40849083441OAI: oai:DiVA.org:his-2806DiVA, id: diva2:201016
Tilgjengelig fra: 2009-03-02 Laget: 2009-03-02 Sist oppdatert: 2017-12-13bibliografisk kontrollert
Inngår i avhandling
1. Mechanical behaviour of adhesive layers: experimental methods, cohesive laws, and fracture mechanics
Åpne denne publikasjonen i ny fane eller vindu >>Mechanical behaviour of adhesive layers: experimental methods, cohesive laws, and fracture mechanics
2008 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Abstract [en]

Adhesive joining is today viewed as one of the key technologies to achieve decreased emissions in the automobile industry. To decrease weight, optimal material selection often results in different materials for different parts. This leads to the necessity to join mixed material. Here, the use of adhesives is the most promising joining technology. For a rational design process, good models for strength analysis of adhesively joined structures are essential. With cohesive modelling, fracture of the adhesive layer is modelled with a stress-deformation law. This law - often denoted a cohesive law - gives the traction exerted on the adherends due to the deformation of the adhesive layer. This thesis is concerned with experimental methods to measure cohesive properties of engineering adhesives and standardized methods to measure the fracture energy of adhesives. A new method to measure cohesive laws is developed. With this method, the cohesive law of an epoxy adhesive is measured in shear. In peel loading, with elastically deforming adherends, the cohesive law is shown to be independent of the geometry of the specimen. If the adherends deform plastically the fracture energy increases. Experiments are performed in order to determine the temperature dependence of the cohesive layer for an epoxy adhesive. It is shown that the peak stress is strongly dependent on the temperature while the fracture energy shows only small temperature dependence. Experiments are also performed to study the influence of strain rate in peel and shear loading. The experiments show that the peak stress increases with an increasing strain rate and that the fracture energy increase in peel loading and decreases in shear with increasing strain rate. A new method to experimentally determine the relation between damage and plasticity in the adhesive during the fracture process is developed. For the present adhesive, it is shown that only minor plasticity occurs during the fracture process in peel loading. For peel, several commonly used methods to evaluate the fracture energy using the double cantilever beam specimen are critically studied. For some methods the error in evaluated fracture energy is larger than 40 %. It is shown that the evaluated fracture energy is more dependent on the choice of method than on the cohesive properties of the adhesive layer.

sted, utgiver, år, opplag, sider
Chalmers tekniska högskola, 2008. s. 16
Serie
Doktorsavhandlingar vid Chalmers tekniska högskola, ISSN 0346-718X ; 2816
Emneord
experimental method, adhesive layer, cohesive law, fracture, fracture energy, energy release rate, peel, shear
HSV kategori
Forskningsprogram
Teknik
Identifikatorer
urn:nbn:se:his:diva-2941 (URN)978-91-7385-135-0 (ISBN)
Disputas
2008-10-06, 13:00 (engelsk)
Opponent
Tilgjengelig fra: 2009-04-03 Laget: 2009-04-03 Sist oppdatert: 2017-11-27bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Biel, AndersStigh, Ulf

Søk i DiVA

Av forfatter/redaktør
Biel, AndersStigh, Ulf
Av organisasjonen
I samme tidsskrift
Engineering Fracture Mechanics

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 1199 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf