his.sePublikasjoner
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
A closed-form solution to statically indeterminate adhesive joint problems — exemplified on ELS-specimens
Högskolan i Skövde, Institutionen för teknik och samhälle.
Högskolan i Skövde, Institutionen för teknik och samhälle.
2008 (engelsk)Inngår i: International Journal of Adhesion and Adhesives, ISSN 0143-7496, E-ISSN 1879-0127, Vol. 28, nr 7, s. 350-361Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

A beam/adhesive-layer model is developed. For this model a closed-form solution method applicable to arbitrary boundary conditions is presented. This enables the solution of a large number of practical problems which may be statically indeterminate. The stress state in the adhesive layer and the adherends of the beam/adhesive-layer model is also scrutinized. The method is exemplified in an analysis of the end-loaded split (ELS) specimen, commonly used to determine fracture energies of adhesive layers. The effect of the flexibility of the adhesive layer on the energy release rate and the critical crack length for stable crack growth is examined. Both symmetric and unsymmetric ELS-specimens are studied.

sted, utgiver, år, opplag, sider
Elsevier, 2008. Vol. 28, nr 7, s. 350-361
Emneord [en]
C. Fracture mechanics, C. Stress analysis, C. Joint design, Beam/adhesive-layer model
HSV kategori
Identifikatorer
URN: urn:nbn:se:his:diva-2528DOI: 10.1016/j.ijadhadh.2007.10.002ISI: 000256843700003Scopus ID: 2-s2.0-42949137074OAI: oai:DiVA.org:his-2528DiVA, id: diva2:134070
Tilgjengelig fra: 2009-01-16 Laget: 2009-01-16 Sist oppdatert: 2017-12-14bibliografisk kontrollert
Inngår i avhandling
1. Mixed mode loaded adhesive layers: from measurement of material data to analysis of structural behaviour
Åpne denne publikasjonen i ny fane eller vindu >>Mixed mode loaded adhesive layers: from measurement of material data to analysis of structural behaviour
2007 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Abstract [en]

In manufacturing of multi-material products, a joining method that is able to cost-effectively assemble components made of dissimilar and similar material, with irregular geometries, is optimal. As an alternative, adhesive bonding is in-creasingly adapted by the industry, which is also used in manufacturing of multi-phase materials. In practice, adhesives are constrained to thin layers. An adhesive as a constrained layer behaves differently compared to the adhesive as a bulk material. In general, adhesive layers are loaded in peel (mode I), or in shear (mode II or III), or in a combination of peel and shear (mixed mode). This thesis deals with mixed mode loaded adhesive layers, from measurement of ma-terial data to analysis of structural behaviour. For studying of structural behaviour of adhesive joints, an integrated approach is developed. Arbitrarily end-loaded single-layer adhesive joints with arbitrary ad-herends of arbitrary length are analysed with the Beam/Adhesive layer (B/A) model. Closed-form solutions are obtained for the adhesive layer as well as for the adherends. For joints with a semi-infinite symmetric geometry, i.e. relative long joints with identical adherends loaded at one end, basic loading cases are obtained. Solutions to these basic loading cases are easy to use in designing of joints with this type of geometry. For nonlinear or general adhesive layers, a mode-dependent cohesive law is de-veloped. The normalized formulation is easy to implement in numerical simula-tions, yet, it captures the characteristics of adhesive layers. For experimental studies, this cohesive law is used to obtain the constitutive behaviour of an adhe-sive layer. The results confirm the ability and suitability of this cohesive law in modelling of adhesive layers. To obtain material data of adhesive layers, experimental methods are developed based on the J-integral. Two specimens, the Mixed mode double Cantilever Beams (MCB) specimen and the Unbalanced Double Cantilever Beams (UDCB) specimen, are designed to allow adhesive layers to be loaded in mixed mode. The MCB-specimen is implemented experimentally and the constitutive behav-iour of the tested adhesive layer is obtained.

sted, utgiver, år, opplag, sider
Chalmers tekniska högskola, 2007. s. 17
Serie
Doktorsavhandlingar vid Chalmers tekniska högskola, ISSN 0346-718X ; 2572
Emneord
adhesive layer, mixed mode testing, cohesive law, J-integral
HSV kategori
Forskningsprogram
Teknik
Identifikatorer
urn:nbn:se:his:diva-2039 (URN)978-91-7291-891-7 (ISBN)
Disputas
(engelsk)
Tilgjengelig fra: 2008-05-09 Laget: 2008-05-09 Sist oppdatert: 2017-11-27

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Alfredsson, SvanteHögberg, Jia Li

Søk i DiVA

Av forfatter/redaktør
Alfredsson, SvanteHögberg, Jia Li
Av organisasjonen
I samme tidsskrift
International Journal of Adhesion and Adhesives

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 1292 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf